Por favor, use este identificador para citar o enlazar este ítem:
https://hdl.handle.net/20.500.12759/3563
Título : | Diseño de un pavimento rígido agregando elastómetro termoplástico en la provincia de Trujillo - La Libertad |
Autor : | Castillo Cerna, César Enrique Sánchez Guzmán, Dante Rodrigo |
Asesor: | Durand Orellana, Rocio del Pilar |
Palabras clave : | Pavimento rígido Elastómetro |
Fecha de publicación : | 2017 |
Institución : | Universidad Privada Antenor Orrego - UPAO |
No. de serie: | T_ING.CIVIL_1419 |
Resumen : | En la presente tesis de investigación se tuvo como objetivo diseñar una mezcla de
concreto agregándole Elastómero Termoplástico para un pavimento rígido como
medida de repavimentación en la ciudad de Trujillo, a través de la técnica del
Whitetopping.
Para el cumplimiento de este objetivo, se determinó un diseño de mezcla para un
concreto de f’c = 280 Kg/cm 2 el al cual se le realizaron dos (2) diseños, una mezcla
convencional y la otra agregando Elastómero Termoplástico, a este último se le
redujo en un 10% la cantidad de agregado fino. Es necesario saber las propiedades
mecánicas de los agregados para determinar las proporciones de estos en la
mezcla, los cuales fueron recolectados de la quebrada de León y se utilizó el
cemento TIPO I de Cementos Pacasmayo por ser el más comercial de la zona.
Los dos (2) tipos de mezcla se sometieron a los mismos ensayos, resistencia a la
compresión con probetas de 11 cm x 21 cm, donde se realizaron nueve (9)
muestras por cada tipo de mezcla, los cuales se ensayaron a 3, 7 y 28 días de
curado. El siguiente ensayo fue el de resistencia a la flexión a través de la
elaboración de vigas con dimensiones de efectuándose el mismo tipo de muestreo.
Así también como los ensayos de asentamiento (Slump), temperatura y peso
específico.
Se desarrolló un método experimental de forma empírica ya que no estaba sujeto
a normatividad, se quiso demostrar la permeabilidad de cada tipo de muestra en
este método, en el cual no se obtuvieron los resultados esperados. In this thesis the research aims to design a mixture of concrete Elastomer Thermoplastic for a rigid pavement as a measure of resurfacing in the city of Trujillo, through Whitetopping technique. In order to fulfill this objective, a mixture design for a concrete of fc = 280 Kg / cm2 was determined, all of which was done two (2) designs, a conventional mixture and another aggregate Thermoplastic Elastomer, the latter was reduced in 10% the amount of fine aggregate. It is necessary to know the mechanical properties of the aggregates to determine the proportions of these in the mixture, which were collected from the Ravine de León and used the cement TYPE I of Cementos Pacasmayo because it is more commercial in the area. The two (2) blend types are joined to the same tests, compressive strength with 11 cm x 21 cm specimens, where nine (9) samples were made for each type of mixture, which were tested at 3, 7 And 28 days of curing. The following test was of the flexural strength through the elaboration of beams with the dimensions of performing the same type of sampling. As well as the tests of settlement, temperature and specific weight. An experimental method was developed empirically since it was not subject to normativity, it was wanted to demonstrate the permeability of each type of sample in this method, in which the expected results were not obtained. |
URI : | https://hdl.handle.net/20.500.12759/3563 |
Aparece en las colecciones: | Ingeniería Civil |
Ficheros en este ítem:
Fichero | Descripción | Tamaño | Formato | |
---|---|---|---|---|
REP_ING.CIVIL_CÉSAR.CASTILLO_DANTE.SÁNCHEZ_DISEÑO.PAVIMENTO.RÍGIDO.AGREGANDO.ELASTÓMERO.TERMOPLÁSTICO.TRUJILLO.LA.LIBERTAD.pdf | CÉSAR.CASTILLO_DANTE.SÁNCHEZ_DISEÑO.PAVIMENTO.RÍGIDO.AGREGANDO.ELASTÓMERO.TERMOPLÁSTICO.TRUJILLO.LA.LIBERTAD | 3,05 MB | Adobe PDF | Visualizar/Abrir |
Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.