Por favor, use este identificador para citar o enlazar este ítem: https://hdl.handle.net/20.500.12759/10978
Título : Diseño y modelamiento hidráulico de una bocatoma para mejorar el sistema de riego en el Centro Poblado - Buena Vista, Distrito de Chao, Virú 2021
Autor : Alcas Andrade, Alexa Aymé
Lizarzaburu Silva, Carlos Gabriel
Asesor: Cabanillas Quiroz, Guillermo Juan
Palabras clave : Bocatoma
Diseño Hidráulico
Fecha de publicación : 2023
Institución : Universidad Privada Antenor Orrego
No. de serie: T_CIVIL_2257
Resumen : La presente Tesis “Diseño y Modelamiento hidráulico de una bocatoma para mejorar el sistema de riego en el Centro Poblado – Buena Vista, Distrito de Chao, Virú 2021”, fue elaborada con el objetivo de brindar una solución técnica a la problemática presentada por la falta de caudal para riego de cultivos, debido a que no cuentan con una infraestructura adecuada para derivar el caudal necesario a las diferentes hectáreas en el centro poblado en mención. Actualmente, la Junta de usuarios del Sector Hidráulico Menor Chao cuenta con 17 usuarios en el Sector San Roberto, 13 usuarios en el Sector Luna Alto y de la provincia de Virú y departamento de La Libertad. Usuarios que cultivan productos como palta y maíz amarillo principalmente. Atendiendo a dicha realidad, la presente investigación se ha realizado en beneficio de la referida población tomando en cuenta la necesidad de una estructura hidráulica para obtener una parte del agua disponible en una corriente de agua (cauce del río), y darle un adecuado y eficiente uso. Aunado a lo anterior , se describe el procedimiento con el cual se realizó el diseño hidráulico, partiendo de las precipitaciones máximas anuales, información que se encuentra en las estaciones pluviométricas, claro está en el área de estudio; delimitando cuenca según la orografía hasta el punto de salida donde se ubica la infraestructura, para determinar nuestro tiempo de concentración para saber el tiempo necesario en que el agua por escorrentía llega hasta el punto definido y por último obtener nuestro caudal para diseñar la bocatoma, aplicando método de Creager según el T (período de retorno) y así dimensionar la Infraestructura acorde a las condiciones técnicas obteniendo una alternativa de solución que cubra las necesidades de la población actual y futura. Finalmente, luego de realizar el diseño hidráulico de la bocatoma, se procede a realizar la simulación hidráulica para determinar si cumple en el ancho del cauce con el caudal de máxima avenida según período de retorno, para posteriormente discutir los resultados obtenidos, y las acciones a tomar para beneficio de la población de la Junta de usuarios del Sector Hidráulico Menor Chao.
The present thesis ""Design and hydraulic modeling of an intake to improve the irrigation system in the Populated Center - Buena Vista, District of Chao, Virú 2021"", was elaborated with the objective to provide a technical solution to the problems for the lack of flow for irrigation of crops, because they do not have correct infrastructure to derive the necessary flow to the different hectares in the zone. Currently, the Board of Users of the Minor Chao Hydraulic Sector has 17 users in the San Roberto Sector, 13 users in the Luna Alto Sector and province of Viru, in the departament of La Libertad. Users cultivate mostly avocado, vegetables and yellow corn. According to this reality, the present investigation, has been made for the benefit of the population, taking into account the need for a hydraulic structure to obtain part of the water available in a stream (river channel), and give it proper and efficient use. In addition, we describe the procedure of the hydraulic design, based on the maximum annual rainfall, information found in the pluviometric stations, of course, in the study area; delimiting the basin according to the orography to the exit point where the infrastructure is located, to determine our concentration time to know the necessary time in which the runoff water reaches the defined point and finally obtain our flow to design the intake, applying Creager method such as T (return period) and so dimension the Infrastructure according to the technical conditions obtaining an alternative solution that covers the needs of the current population and future. Finally, after of analyze the hydraulic design of the intake, proceeds with the hydraulic simulation to determine if it complies with the width of the channel with the maximum flood flow according to the return period, to lately discuss the results obtained, and the actions to be taken for the benefit of the population of the Board of Users of the Minor Chao Hydraulic Sector.
URI : https://hdl.handle.net/20.500.12759/10978
Aparece en las colecciones: Ingeniería Civil

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
REP_ALEXA.ALCAS_CARLOS.LIZARZABURU_DISEÑO.Y.MEJORAMIENTO.pdfALEXA.ALCAS_CARLOS.LIZARZABURU_DISEÑO.Y.MEJORAMIENTO7,02 MBAdobe PDFVisualizar/Abrir
AUTORIZACION.ALEXA.ALCAS_CARLOS.LIZARZABURU.pdf
  Restricted Access
776,9 kBAdobe PDFVisualizar/Abrir  Request a copy
TURNITIN.ALEXA.ALCAS_CARLOS.LIZARZABURU.pdf
  Restricted Access
22,48 MBAdobe PDFVisualizar/Abrir  Request a copy


Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons